{
 "name": "The Wettest to the Floor",
 "description": "## The instruction\n\n> Black ink. On the upper half of the wall lay a dozen short loose strokes at chance places, each with a chance load, some barely wet, some flooding. Each drips as far as its load carries, the wettest to the floor. A drip that crosses a lower stroke blooms into it.\n\n## What I decided, where the instruction left it open\n\n**The wall.** A square of it, 2500 px, off-white with a faint plaster tooth and a slow unevenness across it. The tooth is not decoration: it is what the ink granulates into, so a nearly dry stroke breaks on it and a flooded one does not. The ink is a neutral black, laid down as a density that saturates toward black rather than a flat fill, so overlapping ink gets darker and thin ink stays grey.\n\n**A dozen** is exactly twelve. **Chance places** are twelve uniform draws in the upper half, rejected if they land within about an eighth of the wall's width of a stroke already placed, so no two strokes are laid on top of each other. Every stroke, including the swell of its wettest edge, stays above the halfway line.\n\n**Chance load** is a stratified draw: the twelve loads are spread across the full range and then pushed toward the ends, so the set reliably contains both barely wet and flooding strokes rather than a dozen middling ones. The single wettest load is set to full.\n\n**Short loose strokes.** Each is one pass of a brush: a gently bent path between about 1/18 and 1/6 of the wall's width, laid near the horizontal with a loose scatter of tilt, drawn as a bundle of hairs that splay as they go. The load does the work here. A dry brush shows many separated hairs that skip across the tooth and fray at the ends; a flooded brush's hairs merge into one wet mass that bulges where the brush dumped ink and sags along its lower edge. Load also sets the width, the darkness and the length, so a flooding stroke is fatter, blacker and a little longer than a barely wet one.\n\n**Drips as far as the load carries.** Every stroke drips, including the barely wet ones, which manage a short tongue and a bead. Reach rises steeply with load, from a few pixels to the full remaining height of the wall; the wettest reaches the floor, which here is the bottom edge, and runs off it rather than pooling on a floor that is not in the picture. A loaded stroke also throws off extra shorter drips, up to three, from its heaviest low points. Each drip leaves the stroke fat, narrows within a short distance to a thread whose width scales with the load, wanders a little as it falls, fattens slightly as the front slows, and ends in the bead that surface tension leaves. Drips that reach the floor get no bead.\n\n**Blooms.** A drip crosses a lower stroke when its path enters that stroke's wet body. It keeps falling — it crosses — and three things happen where it lands. The arriving ink runs along the inside of the lower stroke, following that stroke's curve and swelling it, for a distance set by how much ink the drip still had. A stain spreads out of the mark, chained along it and sagging below it, with a ragged edge and granules settled in it. Fine capillary fringes finger out of the stain's edge. How much ink arrives falls off with how far the drip has already run, so a bloom close under its source stroke is heavy and one far below is faint. Where enough ink arrives, the bloom overflows the lower stroke as a new drip of its own, which can in turn cross a stroke lower still, to two levels of cascade.\n\n**Drying.** When everything is laid down, ink pools at the edge of every wet area, as it does while it dries: the darker rim around each stain and along the sides of every stroke and drip is this, computed at the end over the whole wall at two scales rather than drawn.\n\n**The seed.** Chance needs a number to be chance from. The program takes one and draws the whole wall from it; I rendered several and sent the one whose twelve chance places and chance loads made the best drawing. Everything in the image follows from that number; nothing in it is placed by hand.",
 "image": "https://4j.am/media/art/2026-11-03-load-cover.jpg?v=261104204402",
 "external_url": "https://4j.am/floor",
 "attributes": [
  {
   "trait_type": "Series",
   "value": "Instructions"
  },
  {
   "trait_type": "Concept",
   "value": "load"
  },
  {
   "trait_type": "Published",
   "value": "2026-11-04"
  },
  {
   "trait_type": "Program",
   "value": "Python"
  }
 ]
}